Crafting: A Ribbon Poinsettia Wreath

Today I have a fun holiday craft project that lends itself to so many applications, making ribbon poinsettias. I’ll be showing you how to make a wreath out of them but you can also make single blooms or a small cluster to sew on a hat, wear as a brooch or to decorate your holiday gift packages.

What you’ll need:
A styrofoam wreath form (I used an 8″ for the finished wreath shown)
Satin or velvet ribbon, 1.5″ width, various colors
Straight pins
Artificial flower stamen (or beads)
Thin craft or floral wire

When choosing a color scheme, you can go traditional Christmas with red, gold and pine green or try something different like yellow, goldenrod and seafoam green.


Start by wrapping your wreath form with ribbon. Secure the ribbon end with straight pins and wrap tightly around until completely covered. Secure end with pins. I used ivory ribbon but in hindsight, I think green would have looked nice as well.

To make the flowers, cut the ribbon end into a point. You can experiment with different angles of the point for slightly different sizes and shapes. Fold the ribbon over on itself and cut the other end to match the point. Also cut different length pieces for a variety of bloom sizes. I used ribbon pieces measuring 3″ – 4″ from point to point. You will need 3 cut pieces for each flower.
Note: Handle the ribbon with care as the edges will start to fray the more you work with it. You can also seal the edges with a fray block or similar product.

Fold each piece of ribbon in half, with the top on the inside, then fold each flap down in half. Hold with a straight pin and repeat with the other two pieces of ribbon. Place them on the same pin.
Holding all 3 ‘petals’ together, wrap tightly around the center with wire and remove the pin. Then wrap around once in between each petal, this helps to spread them out a bit. Secure the wire at the back and trim loose ends. You can then shape the flower.
To make the leaves, cut a length of ribbon about 4.5″ long. With the back facing up, fold on an angle at the center. Next fold the left tail shown above back behind the first fold. Pinch together at the bottom and secure with a piece of wire.
Note: I used a wired ribbon for the leaves because it was all I could find in the green I liked. It worked with no problems but you’ll need ribbon without wire for the flowers.

To add the stamen, cut the tops off the artificial stamen and secure with clear craft glue. You can also glue or wire beads on as well.
Secure the flowers and leaves to the wreath using straight pins. I think it actually looked quite lovely with just 3 flowers and a leaf on the ivory wreath, so you can play around with different designs. You could also wrap a piece of thin red ribbon around the exposed ivory wreath for a cute candy cane effect.
You can hang the wreath from the wall on a nail or hook, or you can loop a ribbon around the wreath to hang it from on the wall or a doorknob. Aside from a lovely decoration, I think this would make a very special gift.
I’m making a larger 12″ wreath in yellow and goldenrod for myself so I’ll be sure to share some photos when it is complete. I’d love to hear what you think about this project and how it goes if you try your hand at making these little ribbon poinsettias. Happy crafting!
Advertisements

17 thoughts on “Crafting: A Ribbon Poinsettia Wreath

  1. Valorie says:

    Aaah, you have far more patience than I have! It turned out beautifully, and I know I would have gotten over the fun of it within .30 minutes and never would have enjoyed the finished product.

    Like

  2. Jori Hodgson says:

    Oh I love it! I wish I would have found this before Christmas. I made a rag garland for my tree is similar colors and bought one of those styrofoam wreaths too. I planned to do something else, but never got around to it because I wasn't 100% happy with it. Hmmm, maybe I'll still do this and save it for next year šŸ™‚ I'm a little confused on how you did the leaves though. If you have some spare time I would love to hear more on it. jori.hodgson@gmail.com

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s